Linux version 2.6.23.8 (root@zombie) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) #6 PREEMPT Fri May 30 04:15:57 CEST 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fffc000 (usable)
 BIOS-e820: 000000003fffc000 - 000000003ffff000 (ACPI data)
 BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
Entering add_active_range(0, 0, 229376) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   229376
On node 0 totalpages: 229376
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  Movable zone: 0 pages used for memmap
DMI 2.3 present.
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Built 1 zonelists in Zone order.  Total pages: 227584
Kernel command line: root=/dev/hda5
Found and enabled local APIC!
mapped APIC to ffffb000 (fee00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1822.656 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 906156k/917504k available (2010k kernel code, 10864k reserved, 589k data, 140k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xffffa000 - 0xfffff000   (  20 kB)
    vmalloc : 0xf8800000 - 0xffff8000   ( 119 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc038e000 - 0xc03b1000   ( 140 kB)
      .data : 0xc02f6b68 - 0xc038a024   ( 589 kB)
      .text : 0xc0100000 - 0xc02f6b68   (2010 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3648.34 BogoMIPS (lpj=7296689)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: AMD Athlon(TM) XP 2500+ stepping 00
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf1970, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: enabled onboard AC97/MC97 devices
PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0
PCI: setting IRQ 3 as level-triggered
PCI: Found IRQ 3 for device 0000:00:0f.1
IRQ routing conflict for 0000:00:10.0, have irq 9, want irq 3
IRQ routing conflict for 0000:00:10.1, have irq 9, want irq 3
PCI: Bridge: 0000:00:01.0
  IO window: d000-dfff
  MEM window: bf000000-bfffffff
  PREFETCH window: c0000000-f7ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
Time: tsc clocksource has been installed.
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
NTFS driver 2.1.28 [Flags: R/O].
JFS: nTxBlock = 7080, nTxLock = 56640
io scheduler noop registered
io scheduler anticipatory registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
Boot video device is 0000:01:00.0
lp: driver loaded but no devices found
Linux agpgart interface v0.102
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 64M @ 0xf8000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
PCI: setting IRQ 5 as level-triggered
PCI: Found IRQ 5 for device 0000:00:0b.0
eth0: RealTek RTL-8029 found at 0xb400, IRQ 5, 00:00:B4:5B:1D:0F.
PCI: setting IRQ 10 as level-triggered
PCI: Found IRQ 10 for device 0000:00:09.0
skge 1.11 addr 0xbe800000 irq 10 chip Yukon rev 1
skge eth1: addr 00:0c:6e:d6:07:c2
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
PCI: Found IRQ 3 for device 0000:00:0f.1
IRQ routing conflict for 0000:00:10.0, have irq 9, want irq 3
IRQ routing conflict for 0000:00:10.1, have irq 9, want irq 3
PCI: VIA VLink IRQ fixup for 0000:00:0f.1, from 255 to 3
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0x9000-0x9007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0x9008-0x900f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST380011A, ATA DISK drive
hdb: IC35L060AVVA07-0, ATA DISK drive
hda: selected mode 0x45
hdb: selected mode 0x45
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: RICOH DVD/CDRW MP9060, ATAPI CD/DVD-ROM drive
hdc: selected mode 0x22
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 >
hdb: max request size: 128KiB
hdb: 120103200 sectors (61492 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100)
hdb: cache flushes supported
 hdb: hdb1 < hdb5 hdb6 hdb7 >
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
PCI: Assigned IRQ 10 for device 0000:00:10.4
PCI: Sharing IRQ 10 with 0000:00:11.5
PCI: Sharing IRQ 10 with 0000:00:11.6
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 10, io mem 0xbe000000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v3.0
PCI: Found IRQ 3 for device 0000:00:10.0
PCI: Sharing IRQ 3 with 0000:00:0f.1
IRQ routing conflict for 0000:00:10.0, have irq 9, want irq 3
IRQ routing conflict for 0000:00:10.1, have irq 9, want irq 3
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 9, io base 0x00008800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Found IRQ 3 for device 0000:00:10.1
PCI: Sharing IRQ 3 with 0000:00:0f.1
IRQ routing conflict for 0000:00:10.0, have irq 9, want irq 3
IRQ routing conflict for 0000:00:10.1, have irq 9, want irq 3
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 9, io base 0x00008400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: setting IRQ 4 as level-triggered
PCI: Found IRQ 4 for device 0000:00:10.2
IRQ routing conflict for 0000:00:0f.0, have irq 11, want irq 4
IRQ routing conflict for 0000:00:10.2, have irq 11, want irq 4
IRQ routing conflict for 0000:00:10.3, have irq 11, want irq 4
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 11, io base 0x00008000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
PCI: Found IRQ 4 for device 0000:00:10.3
IRQ routing conflict for 0000:00:0f.0, have irq 11, want irq 4
IRQ routing conflict for 0000:00:10.2, have irq 11, want irq 4
IRQ routing conflict for 0000:00:10.3, have irq 11, want irq 4
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 11, io base 0x00007800
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Using IPI Shortcut mode
input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input1
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 140k freed
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Adapter chains initialized successfully!
[fglrx] CF object manager initialized successfully!
[fglrx]   vendor: 1002 device: 4150 count: 1
[fglrx] Maximum main memory to use for locked dma buffers: 805 MBytes.
[fglrx] ASYNCIO init succeed!
[fglrx] PAT is enabled successfully!
[fglrx] module loaded - fglrx 8.49.7 [May 12 2008] with 1 minors
PCI: Found IRQ 10 for device 0000:00:11.5
PCI: Sharing IRQ 10 with 0000:00:10.4
PCI: Sharing IRQ 10 with 0000:00:11.6
PCI: Setting latency timer of device 0000:00:11.5 to 64
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
SGI XFS with no debug enabled
XFS mounting filesystem hda9
Ending clean XFS mount for filesystem: hda9
Adding 987956k swap on /dev/hda8.  Priority:-1 extents:1 across:987956k
skge eth1: enabling interface